Homeowners comparing deck builders in Wells, ME usually want the same answer first: what will this deck cost, and what sits under the boards? We plan and build new pressure-treated and composite decks and complete replacements, starting with your lot, house connection and access.
Southern Maine Deck Builders plans and builds new pressure-treated wood decks, composite and PVC decks, and complete deck replacements in Wells and across York County.
Planning figures are about $80 per square foot for basic pressure-treated work with a $10,000 minimum, about $100-120 per square foot for complex or upgraded work, and a $15,000 minimum for composite with a project-specific quote. None of these figures is a binding quote.
Each project starts with a site visit covering the house connection, drainage, footings and access. Permit and zoning questions go to the Town of Wells for your specific parcel.
Choosing a deck builder for a Wells home comes down to how clearly the structure, price and scope are explained before anything is built. We put the ledger, footings, framing, stairs and rails in writing alongside the decking you see, so you can compare our proposal line by line and understand where each dollar goes, from demolition to the last railing post.
The right deck material for a Wells home depends on how much upkeep you will accept, how the deck sits in sun and weather, and what you plan to spend. Here is how our three project types compare.
Pressure-treated lumber gives you a sturdy deck at our lowest planning figure, about $80 per square foot for basic work with a $10,000 project minimum. It feels like wood underfoot and can be cut, fastened and repaired with ordinary carpentry.
The tradeoff is upkeep. Wood boards need periodic cleaning and a finish or sealer schedule you keep up with, and boards in full sun can check and move more as they weather.
Composite and PVC boards skip the sanding and staining cycle, which appeals to owners who would rather spend summer weekends on the deck than working on it. They still need cleaning, and the framing underneath is often pressure-treated lumber, so structure matters just as much.
Composite projects start at a $15,000 minimum and are priced from the selected product line. We use that manufacturer's current installation instructions to lay out the joists and specify the board gaps and fixings.
Complete replacement means removing the existing deck, including framing and supports, and building a new structure in its place. We look at the condition of the ledger, posts and joists before recommending it, and we explain what we saw.
Demolition, disposal and any change in size or height belong in the written scope. Replacement work can fall in the complex range of about $100-120 per square foot, depending on what the site needs.
We offer three deck services in Wells, and each one starts from a written scope that names the materials, the structure underneath and the planning price before any work begins. Pick the one closest to your plan and we will refine it on site.
Where the deck attaches to the house, we check the rim and sheathing behind the ledger, then plan flashing that sheds water away from the wall instead of trapping it.
Fasteners, hangers and hidden clips have to suit both treated lumber and the chosen decking. We match hardware to the product's current instructions so metal coatings and fixings stay compatible.
The step from your door to the deck surface should feel natural and leave room for drainage below the threshold. We set the deck height with the door, sill and seasonal board movement in mind.
We start at your property, measuring the house wall, door height, yard slope and the route materials will take from the driveway. If there is an existing deck, we look at its ledger, posts, joists and stairs, then talk through material choices and your rough budget.
Once the written scope is agreed and any required municipal review is complete, we set the footings and build the frame, including the ledger connection, flashing, beams and joists. This is the stage we care most about, because everything you see later depends on how square, level and well-fastened the structure is.
With the frame in place, we install the decking, stairs and railings, then clean up the work area. We walk the finished deck with you line by line against the written scope, pointing out the ledger connection, fasteners and the care steps for the material you chose.
Footing size, spacing and depth depend on the deck's load, its height and what we find in the ground at your address. We confirm current requirements for your parcel before any support goes in.
Water should move away from the house and out from under the deck. We look at grade, downspouts and clearance so the framing can dry between storms instead of sitting damp.
Lumber, decking and tools have to reach the work area. We walk the route from the driveway with you, noting gates, slopes, septic areas, plantings and anything that limits where deliveries can land.
Before building in Wells, we check your specific parcel: where the deck meets the house, how high the door sits, how water crosses the yard and how deliveries reach the site. We also ask if flood mapping or other recorded conditions affect your lot.
Permit and zoning questions belong to the town, so we start with the official Wells municipal website to find the right office and current guidance. We do not predict approval, setbacks or timing; the town answers those for your parcel.
For framing concepts we refer to the American Wood Council's deck resources, and if you choose Trex decking, its current Trex installation downloads guide that install. Your written scope records the parcel findings, structure, materials and price for review before work begins.
Southern Maine Deck Builders builds your Wells deck under owner Adam Bennett. He takes a carpenter's interest in the supporting frame and how it connects to the house and footings, with care for clean joinery.
We are A Seth's Home Pros Company, and that referral parent does not supervise, perform or guarantee construction or handle project payments.
We build decks in Wells and all 57 Maine towns in Cumberland and York counties, including island properties. Island and hard-to-reach sites need a property review for access and scheduling, and our service areas page lists every covered town by county.
The best time to start planning a Wells deck is before you have a date in mind, since site review, scope, material selection and any municipal review all take their own time. We set a schedule only after those steps are clear for your property.
Rail layout shapes both safety and the view. We plan post spacing, guard height and any openings for stairs around how you sit and move, then confirm the layout against current requirements.
Stairs should land where people actually walk, such as toward the driveway, garden or yard. We plan a firm landing at the bottom and keep the route clear of doors and grills.
Afternoon sun changes where you will want to sit, and some boards get warm underfoot. We bring real board samples so you can check color and texture in your own light before choosing.
A deck in Wells costs about $80 per square foot for basic pressure-treated work with a $10,000 minimum, and about $100-120 per square foot for complex or upgraded work. Composite has a $15,000 minimum and a project-specific quote, and minimums apply when area times rate is lower.
| Deck project | Planning figure | Minimum |
|---|---|---|
| Pressure-treated wood | About $80/sq ft | $10,000 |
| Complex or upgraded work | About $100-120/sq ft | Scope dependent |
| Composite | Project-specific quote | $15,000 |
These are planning figures, not binding quotes; your written scope sets the actual price.
Send us a few photos of your house wall, door and yard, plus your rough size and material ideas. We will review them and set up a site visit to measure and talk through scope.
